The use of miter bend is restricted to the low-pressure water line. Applications include rotary and pipe fittings, adapters and couplings, hydraulic pipes and high pressure flanges. Whether you’re simply stocking up on plumbing fittings and repair parts or have a specific project in mind, Ace offers many types of pipe fittings made of different materials. Find your plumbing fitting solutions at Ace, then shop for other essential plumbing repair parts for your home needs. Coupling are also useful if the pipe is broken or leakage occurs.
The cones of the assembly studs are subject to normal wear and must be checked at regular intervals with taper gauges. Each screw sleeve must be used only once for finishing assembly on the pipe; using the same sleeve again may impair its function. This instruction describes the pre-assembly of a cutting ring on the pipe in a pipe screw sleeve or assembly stud. The surfaces of steel fitting bodies, union nuts and cutting rings are protected from corrosion as standard with a CrVI-free zinc-nickel coating conforming to DIN EN 15205.
Prices and availability of products and services are subject to change without notice. No matter what type of pipe you’re replacing or repairing, Ace has what you need to get the job done. And with our selection of plumbing repair parts, you can tackle any job no matter how big or small. Select 2 or more products for side-by-side feature comparison.
The joint is then heated, typically by using a propane or MAPP gas torch, although electrically heated soldering tools are sometimes used. Once the fitting and pipe have reached sufficient temperature, solder is applied to the heated joint, and the molten solder is drawn into the joint by capillary action as the flux vaporizes. “Sweating” is a term sometimes used to describe the soldering of pipe joints. Assembling threaded pipe is labor-intensive, and requires skill and planning to allow lengths of pipe to be screwed together in sequence. Most threaded-pipe systems require the use of strategically located pipe-union fittings in final assembly. Threaded pipe is heavy, and requires adequate attachment to support its weight.
The larger-diameter hub was also called a “bell” because of its shape. Adequate ventilation is essential to remove metal fumes from welding operations, and personal protective equipment must be worn. Because the high temperatures during welding can often generate intense ultraviolet light, dark goggles or full face shields must be used to protect the eyes.
A tee is steadier than a cross; it behaves like a three-legged stool, and a cross behaves like a four-legged stool. A fitting or adapter is used in pipe systems to connect straight sections of pipe or tube, adapt to different sizes or shapes, and for other purposes such as regulating fluid flow. These fittings are used in plumbing to manipulate the conveyance of water, gas, or liquid waste in domestic or commercial environments, within a system of pipes or tubes. Pipe fittings are essential for all plumbing applications.
Fittings for central vacuum systems are similar to DWV fittings, but are usually of thinner and lighter construction because the weight of the materials conveyed is less. Vacuum-system designs share with DWV designs the need to eliminate internal ridges, burrs, sharp turns, or other obstructions which might create clogs. Non-return or check valves allow free flow of a fluid in one direction, but prevent its flow in a reverse direction. They are often seen in drainage or sewage systems, but may also be used in pressurized systems. Isolation valves are used to temporarily disconnect part of a piping system, to allow maintenance or repair, for example.
Push-to-pull fittings are a type of easily removed compression fitting that allows pipes to be connected with minimal use of tools. These fittings are similar to regular compression fittings, but use an O-ring for sealing and a grip ring to hold the pipe. The main advantage is that it can easily be removed and re-used, it is easy to assemble, and the joints are still rotatable even after assembly. The pipe end should be square so it sits against the stop in the fittings and does not create turbulence, and needs to be a clean cut to avoid damaging the O-ring during insertion.
Socket weld and Threaded Pipe Fittings are forged products and classified based on their pressure-temperature rating. These fittings are available in four pressure-temperature rating class. It used to connect pipe to pipe or pipe to swage or nipple. Click the spin controls to enter number of pipe fittings for each pipe section. Our customer service team sits at the core of our business and is on hand to help you with your requirements and provide one to one assistance.
Isolation valves are typically left in either a fully open or fully closed position. A given isolation valve may be in place for many years without being operated, but must be designed to be readily operable whenever needed, including emergency use. Since the alignment stop is missing, it is up to the installer to carefully measure the final location of the slip coupling to ensure that it is located correctly. If there’s a pipe needing cut or bent, we have the equipment to help make it happen.